Skip to main content
Best Anti Vibration Pads for Washers in 2026 — Sized to the Foot, Honest About What They Cannot Fix

Best Anti Vibration Pads for Washers in 2026

Sized to the Foot, Honest About What They Cannot Fix

4 picks compared · prices, ratings and stock checked November 5, 2026

Our Top Pick

For most washers with feet under 1.75 in across, the ELEON Anti Vibration Pads by Empire of Electronics, which ship with a bubble level. If your front loader has wider feet, the Sumato Stuff HexaGrip pads fit feet up to 2.5 in.

4.3 on Amazon · 5,018 ratings

Quick answer

Anti vibration pads for a washer are worth buying if the machine is level and still walks or buzzes during the spin; they will not cure a washer that shakes from worn suspension, a failed drum bearing or shipping bolts left in. The ELEON Anti Vibration Pads by Empire of Electronics are the default pick, rated 4.3 stars across 5,018 Amazon ratings, and they include a bubble level. Measure first: the ELEON cups fit round feet under 1.75 in and need about 1 in of clearance above the washer, while the Sumato Stuff HexaGrip pads take feet up to 2.5 in.

Our Picks at a Glance

Every pick below is currently stocked — ratings and stock read from Amazon on 5 November 2026.

How this page was made: we compare the current Amazon listings, the makers' published specs and what verified buyers report, then rank by fit for the job. Ratings, review counts and stock are read from Amazon and dated. We earn a commission on purchases through our links; it does not change the order. Reviewed by Marcus Reed, IICRC-certified Water Restoration Technician.

Full Reviews

Each pick in detail: what the listing states, what buyers report, and where it falls short.

#1
Best Overall

Check price

on Amazon ↗

Listing verified 5 Nov 2026

Empire of Electronics ELEON Anti Vibration Pads with Tank Tread Grip (4 Pack + Bubble Level, Feet up to 1.75 in)See it on Amazon ↗

Quick Verdict

ELEON Anti Vibration Pads by Empire of Electronics: the safe default for feet under 1.75 in, with a level in the box.

Key Specs

Pack

4 rubber pads plus a bubble level

Foot size (stated)

Round feet under 1.75 in diameter only; the listing says it is not universal

Clearance (stated)

Needs about 1 in of clearance above the washer

Grip

Tank-tread pattern on the base

Excluded models (stated)

Several Samsung top loaders, listed by model number on the product page

Install

Tilt the machine and slide a pad under each foot; no tools needed per the listing

Pros

  • The largest buyer record among the pads compared here
  • Ships with a bubble level, and the listing itself says leveling is what stops walking
  • States its limits plainly: foot diameter, clearance and the Samsung models it does not fit
  • Cup shape holds each foot so the pad cannot slide out from under it

Cons

  • Will not take feet 1.75 in or wider, which rules out some newer front loaders
  • Raises the machine, so a washer under a counter or tight shelf may no longer fit

Suited to

A standard top or front loader with round feet under 1.75 in that walks on a level, hard floor

Our take

This is the listing that tells you what a pad cannot do, which is why it leads. It says outright that leveling is the fix for walking and puts a bubble level in the box, so the pads arrive with the tool for the step that matters most. Before ordering, measure one foot across its base and check the gap between the top of the washer and anything above it, because the listing asks for about 1 in. If you own a Samsung top loader, compare your model number with the excluded list on the product page. Once fitted, the cups stop the feet sliding on tile, vinyl or sealed concrete.

Check today's price on Amazon →

Affiliate link — commission at no extra cost to you

Compare elsewhere

These open a search for this model. We quote prices only where we can verify them — Amazon, Sylvane and eBay.

#2
Best for Wide Feet

Check price

on Amazon ↗

Listing verified 5 Nov 2026

Sumato Stuff HexaGrip Anti Vibration Pads for Washer and Dryer (4 Pack, Feet up to 2.5 in)See it on Amazon ↗

Quick Verdict

Sumato Stuff HexaGrip pads: the fit for feet up to 2.5 in, with sensible leveling advice on the listing.

Key Specs

Pack

4 rubber pads, one set per appliance

Foot size (stated)

Fits feet up to 2.5 in

Grip

Dual HexaGrip on the base plus a top-side grip

Contact area (claimed)

60% more floor contact than similar pads, per the listing

Floors (stated)

Any hard surface floor

Setups (stated)

Front and top loaders, dryers, combo units, stacked pairs and pedestals

Pros

  • Takes feet up to 2.5 in, wide enough for many larger front loaders
  • The listing tells you to level the washer before fitting the pads
  • Names stacked units and pedestals, which many listings skip
  • Advises buying a second set for the dryer so the pair sits at the same height

Cons

  • The 60% contact figure is the seller's own comparison, with no method given
  • Pad height is not stated on the listing, so check the clearance above a stacked or under-counter pair with the seller

Suited to

Front loaders with wide feet, pedestal setups, and anyone who wants matching sets under a washer and dryer

Our take

Foot size is the first thing that decides whether a pad works, and this is the pick when your feet are too wide for the common 1.75 in cup. A foot that sits on the rim of a too-small cup is worse than no pad, because it rocks. The listing also gets the sequence right: level the washer, then slide the pads under. Treat the 60% extra contact as marketing until someone publishes how it was measured, and judge the pads on the stated fit and the buyer reports. If the washer and dryer sit side by side under a counter, buy two sets so the tops line up.

Check today's price on Amazon →

Affiliate link — commission at no extra cost to you

#3
Simplest Low-Profile Pick

Check price

on Amazon ↗

Listing verified 5 Nov 2026

IdeaWorks JB6368 Washing Machine Anti-Vibration Pads (4 Piece Set, 2.5 in x 0.8 in)See it on Amazon ↗

Quick Verdict

IdeaWorks JB6368: the low 0.8 in option for tight spaces, with less fit detail on the listing.

Key Specs

Pack

4 pads, black

Size (stated)

2.50 in diameter x 0.80 in

Use (stated)

Washers and dryers

Install

Slide one under each corner

Foot cup size

Not stated on the listing

Pros

  • At 0.8 in, the lowest stated height of the pads compared here
  • A long-running listing with a large buyer record and an Amazon's Choice badge
  • Nothing to assemble: one pad per corner

Cons

  • The listing calls the pads universal but gives only the outer size, not the recess the foot sits in
  • Thin on detail compared with the ELEON and Sumato listings, and no level included

Suited to

A machine with modest walking where every fraction of an inch of height matters

Our take

The 0.8 in height is the reason to choose this set. Under a counter, in a closet with a shelf, or in a stacked pair, a thicker pad can push the machine into something above it. The weakness is the listing: it says the pads suit all washers and dryers but only states the outer diameter of 2.5 in, not the size of the recess your foot drops into. Measure your feet and compare them with the product photos, and read the buyer questions on the listing for your washer model before you order. Bring your own level, because none is included.

Check today's price on Amazon →

Affiliate link — commission at no extra cost to you

#4
Best for Concrete Floors

Check price

on Amazon ↗

Listing verified 5 Nov 2026

phepetroll Ribbed Rubber and EVA Anti Vibration Pads (4 Pack, 4 x 4 x 7/8 in)See it on Amazon ↗

Quick Verdict

phepetroll 4 x 4 in pads: heavy-duty, load-rated squares for a washer on a concrete slab.

Key Specs

Pack

4 square pads

Size (stated)

4 x 4 x 7/8 in

Construction (stated)

Ribbed rubber top and bottom with an EVA middle layer

Load (stated)

60 psi; up to 960 lbs per pad

Other uses (stated)

Air compressors, mini-split condensers, HVAC equipment, treadmills, washers and dryers

Odor (stated)

New rubber may smell; the seller suggests airing or washing the pads

Pros

  • States a load rating, 960 lbs per pad, which no other pad here gives
  • A 4 in square base spreads the foot load across more floor
  • Ribbed on both faces, so it grips a dusty concrete floor and the foot above

Cons

  • Flat ribbed pads with no cup, so the foot is held by friction rather than a rim
  • Made as general equipment pads; the listing gives no washer-specific fit guidance

Suited to

A washer on a basement or garage slab where the floor itself is solid and the pads only need to grip

Our take

These are equipment isolation pads, the kind used under compressors and condensers, and they suit a laundry on bare concrete. The square 4 in base and stated load rating mean there is no doubt the pad can carry a loaded washer. What they lack is a cup, so the foot is held by the ribbed rubber rather than by a rim; set each pad squarely, level the machine on top of the pads, and check after the first few spin cycles that nothing has crept. The 7/8 in height also lifts the washer slightly off a slab that sometimes gets damp.

Check today's price on Amazon →

Affiliate link — commission at no extra cost to you

Buyer's Guide

What to know before you buy.

Level the Washer Before You Buy Anything

Most walking washers are not level, and a pad under an unlevel machine just gives it a softer surface to rock on. Put a level across the top front edge and then front to back. Turn each adjustable foot until the bubble sits in the middle, then tighten the lock nut on each foot against the cabinet so it cannot creep back. Press down on opposite corners: if the cabinet rocks, one foot is not touching the floor. Many front loaders have self-adjusting rear legs that settle when you tip the machine forward and set it down again; the owner's manual describes it. Once the machine stands solid on all four feet, run a spin cycle. If it no longer walks, you may not need pads at all.

What Pads Actually Do

A pad does two jobs. It adds grip, so the sideways push of a spinning drum cannot slide the feet across smooth tile, vinyl or sealed concrete. And it puts soft rubber between the foot and the floor, which takes some of the buzz out of what the floor and walls pass on, most noticeable on an upper floor. That is the whole list. A pad does not change how hard the drum swings, does not correct a load that has bunched to one side, and does not stop a light wood-framed floor from flexing under a heavy machine. Expect a level washer to stay where you put it and sound a little softer, not to stop moving inside its cabinet.

Measure the Foot and the Space Above

Fit decides whether a pad helps or hurts. Tip the washer back slightly and measure one foot across its base. The ELEON cups take feet under 1.75 in, the Sumato HexaGrip pads take feet up to 2.5 in, and the IdeaWorks listing gives only the outer diameter. A foot perched on the rim of a cup that is too small will rock, which is the opposite of what you are paying for. Then check height. Every pad lifts the machine; the ELEON listing asks for about 1 in of clearance above the washer, and the phepetroll squares are 7/8 in thick. Under a counter or a shelf, or in a stacked pair, measure that gap before ordering.

Who Should Not Buy Pads: When the Washer Needs a Repair

Skip the pads and fix the machine if it bangs hard or thumps against the cabinet during every spin, even with a small, evenly spread load. On a top loader that usually points to worn suspension rods; on a front loader, worn springs or shock absorbers. A grinding or rumbling noise that grows with drum speed, or a drum that feels loose when you rock it by hand, suggests a failed drum bearing, which our loose-drum guide covers. A brand-new front loader that shakes violently from the first wash may still have its shipping bolts in the back panel; the installation instructions show where they are. Bunched bedding or a single heavy item is a load imbalance, and redistributing it is the fix.

Floor Type Changes the Choice

On tile, vinyl or sealed concrete, a cupped pad with a patterned base such as the ELEON or Sumato is the usual choice, because the cup stops the foot sliding off. On a rough or dusty basement slab, a wider flat pad such as the phepetroll spreads the load and the ribbed rubber grips the uneven surface. Carpet is a poor base for a washer with or without pads, and the Sumato listing states hard floors only. If the whole floor bounces when the washer spins, the joists are flexing; pads will soften the noise but cannot stiffen a floor, and that is a question for a contractor.

Check Under the Machine While You Are There

Tilting the washer to fit pads is a good moment to look for slow leaks. Water stains, a damp subfloor or rust on the cabinet base point to a hose, pump or door seal problem that is worth fixing before it becomes floor damage. The EPA advises drying wet building materials within 24 to 48 hours to prevent mold growth, and a leak that has been running under a washer for weeks has usually missed that window. If the machine sits on an upper floor or above a finished room, a drain pan under it adds a second line of defense, and replacing old rubber fill hoses with braided ones is a small job while the machine is pulled out.

Frequently Asked Questions

Do anti vibration pads for washers work?

YesFor walking and some of the noise, on a machine that is already level.

The pads add grip so the feet stop sliding on a smooth floor, and the rubber softens the vibration passed into the floor. They do not reduce how hard the drum itself swings, so a washer that shakes from worn suspension, a bad bearing or an unbalanced load will still shake on pads.

How do I stop my washing machine from walking?

Level it first and lock the feet. Adjust each foot until a level reads true side to side and front to back, tighten the lock nuts, and check the cabinet does not rock on opposite corners.

Spread heavy loads evenly in the drum. If a level machine still creeps on a smooth floor during the spin, cupped anti vibration pads are the next step.

Why is my washer shaking violently during the spin cycle?

Usually an unbalanced load, an unlevel machine or a worn part. Bunched bedding or one heavy item throws the drum off center.

If loads are small and even and the machine is level, worn suspension rods on a top loader or worn springs and shock absorbers on a front loader are common causes. On a new front loader, check that the shipping bolts were removed. Pads will not fix any of these.

Are anti vibration pads worth it?

They are worth it when a level washer still walks on tile, vinyl or concrete, or when spin noise carries through an upper floor.

They are not worth it as a substitute for a repair: if the drum bangs the cabinet or the bearing rumbles, the money is better spent on a diagnosis. Measure the foot first, because a pad that does not fit makes rocking worse.

Is it normal for a washing machine to shake?

Some movement is normal; banging is not. A washer drum is suspended so it can move inside the cabinet, and you will see the cabinet shiver as the spin speeds up and slows down.

Loud knocking against the cabinet, the machine moving across the floor, or shaking that is just as bad with a small, even load are signs that it needs leveling or a repair.

Do washer pads work for the dryer too?

YesThe same pads fit most dryers, and a dryer that thumps or squeaks on a hard floor can be quieter on them.

A dryer thumping from inside the drum is a different problem, usually a worn drum roller or belt, and our dryer thumping guide covers it. Buy a second set for the dryer so a side-by-side pair stays at the same height.

Who do I call right now for water damage?

Call (888) 840-6512. The line is answered 24 hours a day, seven days a week, and connects you with an IICRC-certified water damage restoration company that serves your area. A recorded menu picks up first: choose water damage or mold, key in your 5-digit ZIP code, and hold through the short silence while the call is passed to the company.

Describe what you can see — where the water is coming from, how long it has been there, and whether it smells — the more specific you are, the faster the right company is on the line. If the source is a pipe or an appliance, shut the main water valve first. Have four things ready and the call goes quickly: the address, when the water started, what is wet now, and whether you have filed an insurance claim.

Still not sure which of these is your situation? (888) 840-6512 · toll-free · answered 24/7

Sources

  1. EPA — A Brief Guide to Mold, Moisture, and Your Home

Methodology: How we source and verify data · Report an error

How we chose these picks

  • Every pick is a current listing. Stock, star ratings and rating counts are read from Amazon by script and carry the date they were read.
  • Nothing under 4.0 stars makes the list, and the top pick needs a large rating count, so one good week of reviews cannot put it there.
  • Specs are quoted from the listing or the maker, with the test condition behind the number where there is one, and sized against the job rather than the room on the box.
  • Each comparison is reviewed by Marcus Reed, an IICRC-certified Water Restoration Technician, against the IICRC drying standards and public guidance listed under Sources.

Free 2-day shipping

Amazon Prime members pay no shipping on restoration equipment

Dehumidifiers, air movers, and moisture meters qualify for free Prime delivery — bulk items that otherwise cost $15–$40 to ship.

Try Prime free →

Affiliate link — HearthDry earns a bounty if you sign up; costs you nothing extra.

Also Worth Comparing

Best Washing Machine Drain Pans in 2026 — Sized to the Washer's Feet, With or Without a Drain Port, and the Burst Hose No Pan Can Catch

A washing machine drain pan catches drips and small overflows under the washer, and only a pan with a drain port can send that water away instead of holding it. These picks are compared on inside size, wall height, drain port and material, with the gallons-per-inch math and the burst-hose risk that no pan covers.

Read the comparison

Best Washing Machine Hoses in 2026 — Braided Stainless Supply Lines, Elbows for Tight Spaces, and the Shutoff a Hose Still Needs

A washing machine's two fill hoses sit under full house pressure whenever the valves are open, and an old rubber hose that splits keeps releasing water until someone closes the valve. These picks are braided stainless hoses compared on fittings, length, elbows and what each listing actually states, with the replacement habit and the shutoff valve that a better hose does not replace.

Read the comparison

Best Washing Machine Cleaners in 2026 — Tablets, Oxi Powder and Gasket Gel for a Washer That Smells, and the Odors No Cleaner Can Reach

Most washer smells come from detergent and fabric-softener residue that holds moisture inside the tub, the pump area and the door seal, and a monthly cleaner cycle is how you keep it from building up. These picks are tablets, an oxygen powder, a pet-hair formula and a gasket gel compared from their listings and buyer ratings, with the cases where the smell is a clogged filter or drain that no cleaner will fix.

Read the comparison